Skip to main content

mmup mechanical questions 02


MECHANICAL DISCIPLINE
1. Car chassis are: Felix, Rigid, stiff?     
2. What is not a System parameter? Pressure, Temp, specific volume, Heat?                                   
3. Reason for Fast track project?. Future material price, cost reduction? 
4. Barometric gage? Atm,  atm & differential. Diff only?
5. Manometer? Differential, atm?
6. Centripole force?
7. Hooks law?
8. Onset plastic deformation? Yield, plastic, rigid
9. Stress and strain? Proportional
10. Forward plan. early start early finish
11.shahida work in inf mgm project, Run by inf mgm dept and helped through normal procedures by other dept. type of org? functional, projectized, .functional matrix....?
12.car dash board from? Polymer,metal?
13. Differential gear. Reducing speed, changing speed, jerk-off free?                                        
14. Water boiling at which point? Critical, saturation..?
15.what to do in a project to issue AFC according to contract?
16. Sustainability?
17. What phase is under shear? Gas, liquid, metal, fluid?
18.software development process?. Plan.do.chk.act
19.material under failure due to excessive plastic deformation due to? material, Design and dimensions.?
20.change matter from state to state? Process, cycle?
21.thermoplast is due to? heat and pressure and get hard.

1.microphone,and amplifier and speaker sketch:  and ask about input and output.
2. When boiling water in pan. What is constant? Pressure, temp?
3. in delay of contract what is the inacceptable excuse?
4.unit of linear acceleration?
5. When u have project split into small parts, what is the name of activities of estimating resource, cost and time?
6. Name of point where 3 points of matter exists.
7. Cause/effect diagram?
8.failure of material because of excessive deflection, .what is the remedies?
9.what is strength of material?
10.why concrete is reinforced with steel?
11.why does structures develops thermal stresses?
12. Variation from spec. called what?
13. For a test case. What name of doc. Includes all req.chk list?
14.p=density x height x g. What is p?
15. In a cycle of generator eff.70% and turbine 80%.what is the overall eff.?
16. What does strain hardening to a material? Tougher, stiffer?
1)      Force applied in a curved path of a submerged object will result in  a) tangential force b) Normal force c) parallel force d) N/A
2)      An object floats in water, the vertical force applied on the object due to the water pressure is called a) gravity force b) shear force c) bayoncy effect d) None of the above
3)      Energy on the wheels of a moving car is a) kinetic energy b) kinetic energy + translational energy c) kinetic energy + rotational energy
4)      What is centripetal force
5)      Youngs modulus
6)      Car bumper is to a) absorb high speed impact b) low speed impact c) side impact d) NOA
7)      Differential gear in a car is to a) reduce the car speed  b) to assist in changing the speed c) low creep d) to turn the vehicle
8)      Which is continuously under shear stress a) solid b) liquid c) fluid d) gas
9)      How does the thermoplast formed
10)   Stress hardening a) stronger & tougher b) stronger & harder c) stronger and softer
11)   The thermal stress is developed in a body due to a) latent heat b) specific heat c) temp gradiant d) total heat
12)   Ina cycle generator eff is 80 % and turbine eff is 90 %, what is the overall eff?
13)   What is Cause & effect diagram
14)   Ian project cycle , control phase is a) after completing the construction phase b) before starting the construction stage c) during construction stage d) in the entire project cycle
15)   What is result if  water/concrete ratio is increased a) increase in workability b) decrease in workability c) high variation in slum test d) more strong
16)   What is triple point
17)   What is ABET
18)   What will be done after the project is awarded to verify the scope a) appoint project manager b) check the client requirements  c) discuss the critical items with team members
19)   Car brake is a) wear resistant b) heat resistant c) all of the above d) none of the above
20)   Mach number
21)   Reynolds number
22)   Rate of change of fluid is depends on the a) density b) mass c) viscosity d) specific gravity
23)   What is not a dialogue force a) moral b) ethics c) discussion d) law
24)   Past pass in backward calculation in a network diagram
Labels:

Comments

Post a Comment

Popular posts from this blog

mmup mechanical questions 01

mmup mechanical questions 1- A material that makes deformation under sheer stress is : a. Liquid b. Gas c. Solid d. Fluid Answer :d. Fluid 2- To determine the type of turbulent flow in a rough vessel, you require: a. Reynolds number and relative roughness b. Relative roughness c. Mach number and Reynolds number d. Mach number and relative roughness Answer 3- If you have a cup of water at 70 degree Celsius and 1 Atmosphere, the liquid is: a. Saturated liquid b. Saturated vapor c. Condensate liquid d. None of the above Answer : Non of the above 4- Zero velocity of a flow inside a vessel will be: a. At the center b. At the periphery c. At the d. At the Answer 5- If you increase the water-cement ratio in the concrete: a. Concrete will lose its specifications b. Decrease the hardening time of concrete c. Decrease the slump d. Increase the slump Answer 6- If you were awarded a project, you wil...
Post a Comment
Read more

mmup civil questions 01

CIVIL QUESTIONS  Pick up the correct statement from the following: A. Pick up the correct statement from the following: A. The theory of formation of concrete is based on the phenomena of formation of voids B. The bulking of sand is taken into account while volumetric proportioning of the aggregates C. The dry sand and the sand completely flooded with water, have practically the same volume D. The expansion and contraction joints are provided if concrete structures exceed 12 m in length E. All the above Answer: Option E Initial setting time of cement for asbestos cement products should be not less than A. 30 minutes B. 50 minutes C. 75 minutes D. 90 minutes Answer: Option D Pick up the correct ...
Post a Comment
Read more

MMUP registration procedure in 3 Simple Steps

MMUP registration 1) ATTESTATION (EDUCATIONAL CERTIFICATES) Orignal Degree Memo Consolidated Marks Sheet Transcript of Each Semester Marks Bonafide Letter from College/University Medium English /regular student  2) PCC (Police Clearance Certificate)  Get PCC from your Embassy  Then Home country PCC to be attested by Qatar MOFA  Then Open Hunkoomi Account through hukomi website login mme.gov.qa then go to Engineers and Engineers committee, registration of applications  Then Extract a good conduct certificate from the site, print this and take along with your home PCC to  CID office. After one week they will give you Qatar PCC. 3) SUBMISSION OF DOCUMENT login mme.gov.qa then go to Engineers and Engineers committee  Then registration of applications then apply. Upload the documents needed with Personal data. After uploading the documents you will get notification from baladiya to submit original documents. After submitting origi...
Post a Comment
Read more