Skip to main content

mmup mechanical questions 07

mmup mechanical questions

1-The molecular specific heat is  effected by :
A-Pressure
B-Temperature.
C-Pressure and temperature.
D-Number of nuclease  in the atom.

2-As per  NFPA 72 , how often the heat detector shall be inspected:
A-Daily.
B-Weekly
C-Monthly
D-Annually
3-Detector which usually detect heat and smoke is usually called
A-Hetosmoko detector
B-Combined heat and smoke detector .
C-xyz detector.
4-A Device which is used to control the air flow and also shut all the air from entire area is called:
A-Smoke damper.
B-Zone damper.
C-Heat damper
D-Dust damper. 
5- What is the main function of cooling tower?
1-Remove the heat from condenser by mean of water bath .
6-Saturated air is going through silica gel, what will happen to the air :
A-Wet bulb temperature will increase.
B-Wet bulb temperature will decrease.
C-it will undergo adiabatic saturation.
D-Dry bulb temperature will increase
E-Dry Bulb temperature will decrease

7-Activity is usually represented by :
A-Node.
B-Dot
C-Arrow
D-A and C
E-Non of the above.
8-Project initial investment is 2000000, the annual profit of the project is 150000, if 20% rate of return desired, after how many years the initial investment will be gained back:
A-1.1
B-2.2
C-5.5
D-8.8
9-As per NFP 72 , for lobby ceiling configuration  not exceeding 4.6 m height, in which distance A lobby smoke detector shall be located form the centerline of elevator door:

A- 3 m
B-6 m
C-3.2 m
D-6.4 m
 10- how often control valve shall be inspected:
A-Annually
B-half  Annually.
C-Monthly .
D-Daily
11-The pump operating point is defined by :
A-Applying the system head curve in to the pump performance curve.
B –Applying the system required flow rate in to pump performance curve  .

Labels:

Comments

Post a Comment

Popular posts from this blog

mmup mechanical questions 01

mmup mechanical questions 1- A material that makes deformation under sheer stress is : a. Liquid b. Gas c. Solid d. Fluid Answer :d. Fluid 2- To determine the type of turbulent flow in a rough vessel, you require: a. Reynolds number and relative roughness b. Relative roughness c. Mach number and Reynolds number d. Mach number and relative roughness Answer 3- If you have a cup of water at 70 degree Celsius and 1 Atmosphere, the liquid is: a. Saturated liquid b. Saturated vapor c. Condensate liquid d. None of the above Answer : Non of the above 4- Zero velocity of a flow inside a vessel will be: a. At the center b. At the periphery c. At the d. At the Answer 5- If you increase the water-cement ratio in the concrete: a. Concrete will lose its specifications b. Decrease the hardening time of concrete c. Decrease the slump d. Increase the slump Answer 6- If you were awarded a project, you wil...
Post a Comment
Read more

mmup civil questions 01

CIVIL QUESTIONS  Pick up the correct statement from the following: A. Pick up the correct statement from the following: A. The theory of formation of concrete is based on the phenomena of formation of voids B. The bulking of sand is taken into account while volumetric proportioning of the aggregates C. The dry sand and the sand completely flooded with water, have practically the same volume D. The expansion and contraction joints are provided if concrete structures exceed 12 m in length E. All the above Answer: Option E Initial setting time of cement for asbestos cement products should be not less than A. 30 minutes B. 50 minutes C. 75 minutes D. 90 minutes Answer: Option D Pick up the correct ...
Post a Comment
Read more

MMUP registration procedure in 3 Simple Steps

MMUP registration 1) ATTESTATION (EDUCATIONAL CERTIFICATES) Orignal Degree Memo Consolidated Marks Sheet Transcript of Each Semester Marks Bonafide Letter from College/University Medium English /regular student  2) PCC (Police Clearance Certificate)  Get PCC from your Embassy  Then Home country PCC to be attested by Qatar MOFA  Then Open Hunkoomi Account through hukomi website login mme.gov.qa then go to Engineers and Engineers committee, registration of applications  Then Extract a good conduct certificate from the site, print this and take along with your home PCC to  CID office. After one week they will give you Qatar PCC. 3) SUBMISSION OF DOCUMENT login mme.gov.qa then go to Engineers and Engineers committee  Then registration of applications then apply. Upload the documents needed with Personal data. After uploading the documents you will get notification from baladiya to submit original documents. After submitting origi...
Post a Comment
Read more