Skip to main content

mmup mechanical questions 05

mmup mechanical questions


1.      Sustainability?
a.      Economic
b.      Environment
c.       Social
d.      All of the above
2.      For Less discharge, high pressure. Which pump is suitable
a.      Centrifugal pump
b.      Axial Pump
c.       Reciprocating pump
3.      Welding: Prevention of oxidizing of molten metal
a.      Filler material
b.      Flux
c.       Coating
4.      Low calorific value.
5.      Smoke detector inspection.
a.      Semiannually
b.      Annually
c.       Monthly
d.      Daily
6.       Control valve inspection in supervisory
a.      Semiannually
b.      Annually
c.       Monthly
d.      Daily
7.      Bernoulli’s principle
a.      Conservation of energy
b.      Steady flow
c.       Viscous flow
d.      Incompressible flow
8.      Last activity in the work breakdown schedule.
9.      Three types of circuits for alarm
10.  Plastic deformation
11.  Best location to construct a exhibition and convention centre
Near airport
Public bus routes area
Busy pedestrian area
12.  In open car parking structure, openings where not uniformly distributed in the opposite side. What is the minimum percentage opening to be provided in the perimeter
5%
15%
30%
More than 40%
13.  Fire damper
14.  In real world, physical quantities are
Continuous
Discrete
None of the above

Labels:

Comments

Post a Comment

Popular posts from this blog

mmup mechanical questions 01

mmup mechanical questions 1- A material that makes deformation under sheer stress is : a. Liquid b. Gas c. Solid d. Fluid Answer :d. Fluid 2- To determine the type of turbulent flow in a rough vessel, you require: a. Reynolds number and relative roughness b. Relative roughness c. Mach number and Reynolds number d. Mach number and relative roughness Answer 3- If you have a cup of water at 70 degree Celsius and 1 Atmosphere, the liquid is: a. Saturated liquid b. Saturated vapor c. Condensate liquid d. None of the above Answer : Non of the above 4- Zero velocity of a flow inside a vessel will be: a. At the center b. At the periphery c. At the d. At the Answer 5- If you increase the water-cement ratio in the concrete: a. Concrete will lose its specifications b. Decrease the hardening time of concrete c. Decrease the slump d. Increase the slump Answer 6- If you were awarded a project, you wil...
Post a Comment
Read more

mmup civil questions 01

CIVIL QUESTIONS  Pick up the correct statement from the following: A. Pick up the correct statement from the following: A. The theory of formation of concrete is based on the phenomena of formation of voids B. The bulking of sand is taken into account while volumetric proportioning of the aggregates C. The dry sand and the sand completely flooded with water, have practically the same volume D. The expansion and contraction joints are provided if concrete structures exceed 12 m in length E. All the above Answer: Option E Initial setting time of cement for asbestos cement products should be not less than A. 30 minutes B. 50 minutes C. 75 minutes D. 90 minutes Answer: Option D Pick up the correct ...
Post a Comment
Read more

MMUP registration procedure in 3 Simple Steps

MMUP registration 1) ATTESTATION (EDUCATIONAL CERTIFICATES) Orignal Degree Memo Consolidated Marks Sheet Transcript of Each Semester Marks Bonafide Letter from College/University Medium English /regular student  2) PCC (Police Clearance Certificate)  Get PCC from your Embassy  Then Home country PCC to be attested by Qatar MOFA  Then Open Hunkoomi Account through hukomi website login mme.gov.qa then go to Engineers and Engineers committee, registration of applications  Then Extract a good conduct certificate from the site, print this and take along with your home PCC to  CID office. After one week they will give you Qatar PCC. 3) SUBMISSION OF DOCUMENT login mme.gov.qa then go to Engineers and Engineers committee  Then registration of applications then apply. Upload the documents needed with Personal data. After uploading the documents you will get notification from baladiya to submit original documents. After submitting origi...
Post a Comment
Read more